Fendt Slicer

The ultimate mower.

Effective mowing on slopes

So you can really reach every blade, the mower unit on the Fendt Slicer FQ can be moved hydraulically to the side (optional). This clever detail lets you move your mower against the drift of the tractor to effectively prevent losses. When using the Slicer FQ together with a butterfly combination at the rear, this side shift can effectively avoid interrupting a mowing strip on corners. This ensures a clean cut.

	Working width	Number Cutting discs
Slicer 310 FQ	3,12 m	6
Slicer 310 FQ KC	3,12 m	6
Slicer 310 FQ RC	3,12 m	6
Slicer 360 FQ***	3,62 m	7
Slicer 360 FQ KC***	3,62 m	7
Slicer 360 FQ RC***	3,62 m	7

^{*** = Observe country-specific regulations}

Conditioners – the choice is yours

You can opt to equip the Fendt Slicer FQ with a conditioner or use it without a conditioner, e.g. for use on low-growth areas. For perfectly dried feed and the best feed quality, you have the choice between a roller (RC) or a tine conditioner (KC). Both come with direct power transmission through overlying transmission shafts – including overload protection. This guarantees the highest level of efficiency. To respond quickly to harvesting and weather conditions, you can adjust the conditioning intensity of the tine conditioner with a 4-setting counter comb or the infinite-setting pretensioning spring on the upper roller. The swath width and distance between the tractor front wheel and the swath guide plate can be adjusted continuously.

For any terrain

The Fendt Slicer FQ is powered by a spur gear and offers the most innovative technology to ensure you always get the best results. 3D ground adjustment is more than just a phrase for this front mower. The towed 3D ground adjustment overlays across and lengthways. This means you can achieve a perfect and above all clean cut, even on hilly terrain. The mower bar inclination is automatically tracked from -6 to +15°; precisely adapted to the up and down movement of the mower. Your benefits: a constant cutting height, giving the highest quality forage – even under the most difficult conditions.

Inspiring solutions

Because you can fit the Slicer FQ straight onto the front linkage, the centre of gravity is close to the tractor – which lowers the weight to the front axle. 3-way coupling is not necessary. For tractors without EHR you can drive the Slicer FQ in floating mode, using the support chains and with the lower links at a secured adjustment height (750 mm). The draw frame above the mower unit further increases the mower's freedom of movement. To park the front mower, just put the lockable adjustment lever in the park position.

Innovative: the optional hydraulic side shift of the mowing unit by up to 40 cm (20 cm to the right and left) guarantees a clean overlap with a front/rear combination. It can also counteract a drift on the slope.

The hydropneumatic relief using the TurboLift System is a standard feature on the Slicer FQ. You can make infinite settings, completely tool-free. This means that the footprint pressure is always perfectly adapted to the conditions at the time.
The cutterbed-tilt automatically follows the ground contours. If the mower bar dips into a hollow, it tilts forward by up to 6° at the same time.
If the mower bar moves upwards, it automatically tilts up to 15°. This keeps the cutting height consistent and provides full sward protection.
The drawn suspension by means of drawbars, control rods and tow cylinders with tie-rods, overlays across and lengthways. This 3D kinematics perfects the cut even on hilly terrain.
Innovative: the optional hydraulic side shift of the mowing unit by up to 40 cm (20 cm to the right and left) guarantees a clean overlap with a front/rear combination. It can also counteract a drift on the slope.
Freedom of movement with a capital 'F' – with a cross-swing angle of +/-13° and a vertical play of around 650 mm, the Slicer FQ front mower is true flexibility at its best.

For gentle and efficient pulling.

Don't waste time where it's not needed. It's easy to couple the Fendt Slicer FP front mower using the three-point hitch in your tractor's oscillating linkage. The oscillating linkage provides for a diagonal swing clearance of +/- 6.5°. This always guarantees the best possible ground following. On the roads, the mower is automatically centred in the middle position on the oscillating linkage. This provides for a safe driving experience, even on poor roads and forest tracks, and protects the machine. A hydraulic fold-out protective cloth is available as an option, to cut down the set-up time on the field.

	Working width	Number of cutting discs
Slicer 260 FP	2,50 m	4
Slicer 260 FPS	2,50 m	4
Slicer 310 FPK	3,00 m	6
Slicer 3060 FP	3,00 m	6
Slicer 3060 FPSL	3,00 m	6
Slicer 3060 FPKC	3,00 m	6
Slicer 3060 FPRC	3,00 m	6

Clearly more efficient

Quick setup times and high working speeds with the best cutting results and low fuel consumption – the clear advantages of our Fendt Slicer front mowers. A safely-stowed knife box and a holder for the quickrelease key also come as standard. The Fendt Slicer FP is therefore unrivalled when it comes to ease-of-use.

Pull instead of push

Due to the oscillating linkage to which the cutterbed is attached right at the front, the mower is pulled rather than pushed. The spring mounting ensures low ground pressure. This massively reduces fuel consumption and protects the sward. Together with the relieving front power lift control on Fendt Vario tractors, the quality of work is further enhanced with a cutterbed working at a steady contact pressure regardless of the ground contour.

Always the right solution

The specially developed, more compact oscillating linkage of the Fendt Slicer 310 FPK disc mower is provided for highly compact mounting and use with small tractors. This mower is ideal for use in upland regions. Depending on the application, the Slicer FP mower can also be fitted with a tine or roller conditioner, or with a rake.